Why Does Exterior Caulk Crack in San Antonio Heat? (And What Lasts)
Exterior caulk usually cracks because the joint moves more than the caulk can stretch. In San Antonio, sunny walls heat up and cool down every day. Wood trim, siding, and window frames grow and shrink with that heat. A stiff or cheap caulk, a bead that's too thick, or caulk painted before it cured can't keep up, so it splits or pulls loose.
The fix is to cut out the failed caulk, prime any bare wood, and re-caulk with a flexible, paintable exterior sealant. It also matters where you caulk. Some gaps on a house are meant to stay open. Here's how to tell the difference and how to do it right before your next paint job.
Why This Question Comes Up After Every Texas Summer
Homeowners notice it on the wall that gets the most sun. One Texas homeowner on Reddit said the caulk on their south-facing siding cracked and broke off after a brutal summer, and it was the only wall where it happened. A commenter pointed to the likely cause: the siding moved as it heated and cooled, and the caulk pulled apart.
South- and west-facing walls take the hardest hit. They get the most direct sun, so the boards and trim on those sides move the most.
Why Caulk Fails
Sherwin-Williams lists the common reasons in its article on paint cracking over caulk:
The caulk wasn't paintable. Some caulks, like 100% silicone, don't take paint. DAP notes that its 100% silicone sealant is not paintable, so you paint the surface first and caulk after.
Paint went on too soon. If you paint over caulk that hasn't dried, the paint forms a skin first. Then the caulk shrinks underneath and cracks the paint.
The joint was too big. Sherwin-Williams says joints wider or deeper than 1/2 inch need foam backer rod first, so the caulk isn't one huge, stiff plug.
The caulk was stuck on three sides. When caulk bonds to both sides of a gap and the back of it, it can't stretch well. Backer rod or bond-breaker tape lets it grip only the two sides, which gives it the most flex.
It was too cold. That article says to caulk when the air, the surface, and the caulk are all above 40°F, and not when rain is coming.
A thick bead smeared over a gap is another common culprit. As one commenter in that Reddit thread put it, caulk is meant to be a thin line that seals a joint, not a patch to cover big holes.
Which Caulk Holds Up Best Outside
For painted exterior trim and siding joints, look for a paintable "elastomeric" sealant. Elastomeric means it's made to stretch and bounce back. Acrylic urethane products are a common pick. Homeowners and painters on Reddit often name the same few, such as Big Stretch, DAP Extreme Stretch, OSI Quad, and Sherwin-Williams SherMax.
The label tells you how much a caulk can move. Look for ASTM C920 with a class number. A higher class means it handles more movement:
Sherwin-Williams' SherMax data sheet lists it as ASTM C920 Class 35, which the company describes as a 70% total joint movement capability.
DAP's Extreme Stretch meets ASTM C920 Class 25 and is paintable in 2 hours.
A basic acrylic latex caulk is fine for many indoor gaps. Outside, on a wall that bakes in the sun, the flexible exterior sealants are the safer choice. DAP's guide to choosing caulk makes the same point: outdoor joints need a flexible, weather-resistant sealant.
Where You Should Not Caulk
Caulking the wrong gaps can trap water inside your walls and cause peeling or rot.
The horizontal laps on siding. Sherwin-Williams' exterior prep FAQ says not to caulk the lap joints of siding, because they let moisture escape from behind the boards. Caulking them can push that moisture out through the paint.
The laps on fiber cement siding. James Hardie's technical bulletin on joints says it does not recommend caulking the horizontal overlap between planks, and it prefers flashing behind butt joints. For factory-finished ColorPlus siding, it doesn't recommend caulking the butt joints at all.
Brick weep holes. Those small gaps near the bottom of brick walls and over windows are there to drain water. The Brick Industry Association's Technical Note 7 says weeps are required to drain water from the flashing and warns about them getting sealed during maintenance. If bugs are the worry, use weep vents or screens, not caulk.
Places that usually do get caulk: gaps where trim meets siding, around window and door frames, vertical butt joints in wood siding (Sherwin-Williams says any joint between two pieces of wood should be caulked), and corner boards.
How to Fix Cracked Caulk the Right Way
Cut it out. Scrape or slice out all the cracked and loose caulk. Don't caulk over failed caulk. The new bead needs a clean, solid surface.
Clean and dry the joint. Dirt, chalky paint, and moisture keep caulk from sticking.
Prime bare wood. Sherwin-Williams' prep FAQ says to prime bare wood, then re-caulk. Caulk sticks better to a primed surface.
Fill deep gaps with backer rod. Anything deeper than about 1/2 inch gets foam backer rod first.
Lay a modest bead and tool it. Smooth it so it presses into both sides of the joint.
Wait before painting. Follow the dry time on the tube. Painting too soon is one of the main causes of cracking.
Watch the heat. Check the label for surface temperature limits. In San Antonio, that often means working walls once they're in the shade rather than at peak afternoon sun.
Same joints cracking again and again? If caulk keeps failing at the same corners of windows and doors, the house may be moving. That's worth a look before you repaint. Our post on why drywall cracks keep coming back covers how San Antonio's clay soils can move a home.
Older homes: If your home was built before 1978, old paint on trim and siding may contain lead. Scraping it can release lead dust. The EPA's lead renovation, repair, and painting rule covers lead-safe work for paid jobs in older homes.
How We Handle Caulking on Exterior Jobs
Art Vandelay Painting paints siding, stucco, trim, fascia, doors, and wood and metal features across North San Antonio and the Hill Country. On an exterior repaint, prep comes first. We wash, scrape loose paint, fix gaps, and prime bare spots. Approved repairs and caulking are written into your scope, so you know what's being done before work starts.
Exterior work comes with this warranty: "2 year warranty on exterior painting."
FAQ: Exterior Caulk
Can I just caulk over the old cracked caulk?
It's not a good idea. New caulk doesn't bond well to old, failing caulk, and the crack often comes right back. Sherwin-Williams' advice is to dig out caulk that is cracking or pulling away, prime bare wood, and then re-caulk.
Should I use clear or white caulk on painted trim?
White is easier to work with. You can see where the bead is and whether you've covered the joint. A commenter in the Reddit siding thread made the same point: with clear caulk, it's hard to tell if you got full coverage. Either way, make sure it says paintable.
Can I caulk in the summer?
Yes, with care. Read the temperature limits on the tube, since many have a maximum surface temperature. Hot, sun-baked walls can make caulk skin over too fast. Work the shady side of the house and follow the sun around.
Do I have to repaint the whole wall after re-caulking?
Not always, but a patch of fresh paint on a sun-faded wall usually shows. Many homeowners re-caulk as part of a full exterior repaint, or at least repaint the whole section around the repair so it matches.
Get Your Exterior Sealed and Painted Right
If the caulk on your trim, windows, or siding is cracking after another Texas summer, we can take a look and tell you which joints need fresh caulk and which should stay open. We'll put the prep, caulking, and paint in a written scope.
Call 210-940-0055 or request a free estimate. We serve Greater and North San Antonio and nearby Hill Country towns, including Stone Oak, The Dominion, Shavano Park, Helotes, Boerne, Fair Oaks Ranch, and Bulverde. Hours are Monday–Saturday, 8:00 AM–7:00 PM, and Sunday, 12:00 PM–5:00 PM.